Tools with settings
Some operations open as a tool, with settings in the context bar and a live preview in the views.
A card at the bottom of the 3D view has the same settings, with Apply and Cancel. Turn the card off in Settings → Editing → Operation toast.
| Hotkey | Action |
|---|---|
| Enter | Applies the tool |
| Esc | Cancels the tool |
Edge cut
Cuts new edges across faces, between points you .
| Setting | Effect |
|---|---|
| Loop (V) | Cuts a whole loop around the Block |
| Uniform offset (E) | Keeps the loop the same distance from an edge. Needs Loop |
| Flip (F) | Measures that distance from the other side |
| Selection only (G) | Cuts only the selected faces |
| Input | Action |
|---|---|
| Adds a point | |
| Shift | Keeps the cut straight |
| Ctrl | Turns snapping off |
| B | Applies and keeps the tool open |
| Space or Enter | Applies |
Bevel tool
Bevels the selected edges or corners. the handle to set the width.
| Setting | Effect |
|---|---|
| Width | How far the bevel cuts in |
| Steps | 0 to 32 for edges. More steps make it rounder |
| Segments | 1 to 64 for corners. 1 is a flat cut, 2 or more round the corner |
| Shape | 0 to 1. Sets the profile of the curve |
| Soft | Smooths the shading across the bevel |
| Input | Action |
|---|---|
| [ and ] | Decreases or increases the steps or segments |
| Shift | Changes the steps or segments |
| Ctrl | Turns snapping off while you drag |
Corners on open edges are skipped. If the width or segments are too large for the faces around them, the bevel is reduced to fit and the status bar shows the values used.
Inset
Adds a smaller face inside each selected face.
| Setting | Effect |
|---|---|
| Amount | How far the new face is inset |
| Rings | 0 to 16 extra rings of faces between the old and new edges |
Clip
Cuts Blocks along a plane.
| Setting | Effect |
|---|---|
| Keep | Keeps the Front, Back or Both sides |
| Caps | Closes the cut with a face. CtrlShiftX turns it on or off |
| Hotkey | Action |
|---|---|
| ShiftX | Switches the side kept |
| G and F | Rotates the plane in either direction |
| Space | Applies and keeps the tool open |
Mirror
Mirrors Blocks across a plane. It has no settings.
Path extrude
Extrudes a profile along the selected edges.
| Setting | Effect |
|---|---|
| Origin | Sets where the profile is measured from: Absolute or Object |
| Delete profile | Deletes the profile after use |
Bridge tool
Joins two open edges with a curved strip.
| Setting | Effect |
|---|---|
| Steps | 1 to 64 segments along the strip |
| Twist | -16 to 16. Twists the strip along its length |
| UV mode | Sets how the texture runs: Auto, U axis or V axis |
| Repeats U, Repeats V | How often the texture repeats |
| Reset curve | Resets the curve |
Arch
Bends the selected edges into an arch.
| Setting | Effect |
|---|---|
| Steps | 1 to 32 segments |
| Height | How high the arch rises. A negative height arches the other way |
| Offset | Shifts the arch, in metres |
Path tool
Builds a ribbon, rail or pipe along points you , in Object mode.
| Setting | Effect |
|---|---|
| Profile | Sets the shape: Ribbon, Rail or Pipe |
| Width | The ribbon's or rail's width |
| Height | The rail's height |
| Radius, Sides | The pipe's radius and number of sides (3 to 64) |
| Steps | 1 to 32. How smooth the path's curves are |
| Lift | Raises the shape above the points |
| Remove last point (CtrlZ) | Removes the last point |
Mesh projection
Projects the selection onto a surface.
| Setting | Effect |
|---|---|
| Direction | Sets which way it projects: Down, View or Facing |
| Offset | The gap left above the surface |
| Project again (Space) | Projects again from the current position |
Displacement
Sculpts the surface with brushes. See Subdivision and displacement.