Get RAPTOR

Hotkeys

These are RAPTOR's default hotkeys. To change them, use Change hotkeys in Settings → Hotkeys, which opens Unity's Shortcuts window.

Num is the number pad.

Everywhere

HotkeyAction
CtrlPStarts and stops Play
CtrlZ Undoes the last change
CtrlY or CtrlShiftZ Redoes the last undone change
CtrlSpace Opens Materials
ShiftT Applies the active material
ShiftAlt1 to ShiftAlt5 Applies Blockout colour 1 to 5
ShiftZ Maximises the view
ShiftA Frames the selection
[Makes the grid finer
]Makes the grid coarser
M Picks the Ruler

Modes and selection

HotkeyAction
1 Switches to Vertex mode
2 Switches to Edge mode
3 Switches to Face mode
4 Switches to Object mode
SpaceSwitches to the next mode, or applies the Block being made
CtrlA Selects all
CtrlI Inverts the selection
Num + Grows the selection
Num - Shrinks the selection
L Selects the loop
G Selects the ring, or thickens in Face mode
CtrlG Selects the ribs, or opens the UV Editor in Face mode

Gizmos and tools

HotkeyAction
W Picks the Select tool
T Picks the Move gizmo
E Picks the Rotate gizmo
R Picks the Scale gizmo
Q or ShiftS Picks the Resize gizmo
Insert Sets the pivot
End Centres the origin
ShiftB Picks New Block
ShiftP Opens the Polygon tool
ShiftQ Picks a workplane
F Bevels
AltF Opens the Bevel tool
ShiftI Insets
C Opens Edge cut
ShiftX Clips
CtrlShiftXClips with caps
ShiftF Mirrors
ShiftD Opens Displacement

Editing

Some hotkeys depend on the mode. The tool panel shows what each one does in the current mode.

HotkeyAction
ShiftG Repeats the last operation
CtrlB Snaps to the grid
Nudges one grid step
V Connects
ShiftM Merges
N Extends, or detaches
AltN Splits, extracts or separates
B Snaps to the last selected, or bridges
AltB Opens the Bridge tool, or aligns to the last selected
Backspace Dissolves, or combines
ShiftO Collapses
P Fills the hole
I Snaps edge to edge
Y Arches
AltX Opens Path extrude, or pins to the target
AltO Sets the origin to the target
AltE Aligns to the workplane
AltQMakes the workplane from the object
AltT Aligns to the target
AltR Rotates to the target
CtrlNum 2Drops to the surface
CtrlNum 0 Clears rotation and scale
H Makes normals hard, or hides faces
J Makes normals soft
K Resets normals to default
U Unhides all faces

Textures

HotkeyAction
CtrlM Lifts the material
Alt Shifts the texture
Alt[Scales the texture down
Alt]Scales the texture up
Alt, Turns the texture left
Alt. Turns the texture right
CtrlF Welds UVs
ShiftH Hotspots connected faces
AltH Hotspots each face

Mouse

GestureAction
Stroke-selects. Shift adds, Ctrl removes
CtrlShiftBox-selects
in the 3D viewLasso-selects
AltPans the 3D view
in Top, Front or SidePans the view
on a move gizmo handleMoves the pivot
TabMoves the selection by an anchor. Ctrl ignores the grid, Shift copies or extrudes
ShiftMakes the material under the mouse active
CtrlPaints the active material
CtrlShiftCopies the material and its alignment

The Ruler

InputAction
MMeasures without leaving the current tool. The rulers stay after you release
Tap MTurns the Ruler tool on or off
Esc during a Cancels the ruler
CtrlZRemoves the last ruler

In Props, Lights and module tools, tap M instead of holding it.

Tab: pivot and anchors

InputAction
Tap TabSwitches the gizmo between World and Local
TabShows the selection's anchors
Tab an anchorMoves the pivot to it
Tab an anchorMoves the selection by that point onto another Block's corner, edge or face

A square marks a corner anchor, a diamond an edge midpoint and a circle a centre.

Placing points

In the Polygon tool, Path tools and Edge cut:

HotkeyAction
BackspaceRemoves the last point
CtrlZUndoes the last point
CtrlYRedoes the last undone point
EnterApplies
EscCancels

With no points left, CtrlZ closes the tool.

Logic canvas

These work while the Logic drawer has focus.

InputAction
TabOpens Quick Add
C Adds a comment
CtrlFOpens Find
FFrames the selection
HomeFrames everything
CtrlASelects all
CtrlCCopies
CtrlXCuts
CtrlVPastes
CtrlDDuplicates
DelDeletes
Nudges
Alt a wireDeletes the wire